Getting Familiar with Plumbing: Your Starting Point for When Installing a Bathtub
Getting Familiar with Plumbing: Your Starting Point for When Installing a Bathtub
Blog Article
The article which follows in relation to How to Install a Bathtub Yourself is exceptionally remarkable. Don't skip it.
Mounting a bath tub isn't specifically brain surgery, however it does need solid plumbing, woodworking, and also sometimes, tiling abilities. Changing an old bathtub with a new one is also a reasonably challenging project. If the old tub is easily accessible, the task can move immediately; if you have to open up a wall to get rid of the old tub as well as position the new bath tub, the task is a lot harder. In either situation, the task is within a home handyman's abilities, although you will certainly require an assistant to move out the old tub and set in the new one. Make sure you have actually qualified yourself for the job as well as fit attempting it. Rather than employing a contractor to take over a halfway-completed project, it is much better to take into consideration employing one prior to you begin. Chances are you may need an expert plumber to make tube connections.
This post will aid you set up a new bath tub in your shower room if you have already gotten a new tub as well as do not require to transform the setup of your previous water pipelines.
Your devices as well as material list ought to consist of the following:
Getting ready for the Installation
To start with, the supporting frame provided with the bathroom needs to be fitted (if required) according to the manufacturer's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is very important to see to it that if the faucet features a plastic washing machine, it is fitted between the bathroom and also the taps. On a plastic bathroom, it is also sensible to fit a supporting plate under the faucets unit to stop pressure on the bathtub.
Fit the adaptable tap ports to the bottom of the two faucets using 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet via the hole in the bath. Use the nut supplied by the producer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make certain you utilize all of the supplied washers.
Connect the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Link the bottom of the overflow tube in a comparable manner.The bath ought to currently prepare to be suited its final placement.
Removing Old Touches
If you require to change old faucets with new ones as a part of your setup, then the first thing you ought to do is disconnect the water supply. After doing so, activate the faucets to drain pipes any type of water continuing to be in the system. The procedure of eliminating the existing taps can be fairly problematic as a result of the limited gain access to that is commonly the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the taps. Have a fabric all set for the remaining water that will certainly originate from the pipelines. Once the supply pipelines have actually been removed, make use of the same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the single faucets from turning during this procedure. As soon as the taps have actually been removed, the holes in the bath/basin will have to be cleaned up of any kind of old securing compound.
Prior to proceeding to fit the brand-new faucets, compare the pipe links on the old taps to the new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is needed for the brand-new taps to fit.
Mounting the Bathtub
Making use of both wooden boards under its feet, place the tub in the needed setting. The wood boards are practical in equally spreading the weight of the tub over the area of the boards rather than focusing all the weight onto four tiny factors.
The following goal is to ensure that the bathtub is leveled all round. This can be accomplished by inspecting the level and also changing the feet on the tub until the spirit level reviews degree.
To install faucets, fit all-time low of the furthest flexible faucet adapter to the suitable supply pipe by making a compression join; after that do the exact same for the various other faucet.
Turn on the water supply as well as inspect all joints as well as new pipework for leakages and tighten them if necessary. Load the bathtub and also examine the overflow electrical outlet and also the normal electrical outlet for leaks.
Ultimately, fix the bathroom paneling as described in the producer's instruction manual. Tiling and also securing around the bathtub ought to wait till the bathtub has actually been made use of at least once as this will certainly resolve it right into its last setting.
Fitting New Touches
If the tails of the new taps are plastic, after that you will certainly require a plastic port to prevent damages to the string. One end of the connector fits on the plastic tail of the faucet as well as the various other end gives a link to the current supply pipes.
If you need to fit a monobloc, after that you will need decreasing couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next off, position the tap in the placing hole in the bath/basin making certain that the washers remain in place between the tap as well as the sink. Safeguard the faucet in place with the producer given backnut. As soon as the tap is firmly in place, the supply pipelines can be linked to the tails of the taps. The taps can either be connected by using corrugated copper piping or with normal faucet connectors. The previous kind should be attached to the tap ends first, tightening up just by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Bathtub
In the area where the bathroom fulfills the ceramic tile, it is necessary to seal the joins with a silicone rubber caulking. This is essential as the installation can move sufficient to break an inflexible seal, triggering the water to pass through the wall in between the bath and also the tiling, resulting in issues with dampness and also feasible leaks to the ceiling listed below.
You can pick from a variety of coloured sealers to assimilate your components and installations. They are sold in tubes as well as cartridges, as well as can securing gaps up to a size of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with twists of drenched paper or soft rope. Bear in mind to always fill up the bathtub with water before securing, to enable the activity experienced when the tub is in usage. The sealant can split rather very early if you do not take into account this motion prior to securing.
Alternatively, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise conveniently available on the market. It is advisable to fit the floor tiles using waterproof or water-proof adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We hope you liked our part on A Step-by-Step Guide to Installing a Bathtub. Many thanks for taking time to read through our blog post. Enjoyed reading our blog? Please share it. Help somebody else discover it. I love reading our article about A Step-by-Step Guide to Installing a Bathtub.
Effective fix? Call! Report this page